WHB04无线电子手轮 手摇脉冲发生器 手脉 说 明 书
The Manual For Fully functional Wireless Handle for Engraving machine
Model：WHB04
版本号（Version）： V1.0
一、外观结构说明 （Structure Description）
注意：当低压指示灯亮的时候，表示电池电量快用完了，建议更换电池。
Note：When the Low voltage indicator LED light；the battery is completely；Proposed to replace the battery
二、装箱配件说明 （Packing Parts）
1．接收器（Wireless USB Receiver）：1只（one ）
2．无线手柄（Wireless Handle）：1只（one ）
3．说明书（Manual）：1份（（one ）
| 产品名称 Name | 工作电压 Voltage | 工作电流Current | 备注 Note |
| 无线USB接收器Wireless USB Receiver | 4.5V—5.0V | 小于 50ma
Less than 50ma | |
| 无线手柄
Wireless Handle | 1.5V—3.0V | 平均电流小于2ma
Average Current Less than 2ma | 2000MAH的2节电池能使用2个月 Use of time More than 2 months USE Two 2000MAH Battery |
注意: 无线电子手轮(手摇脉冲发生器 手脉 雕刻机手轮)采用2节AA高容量电池. 当低压指示灯亮的时候，表示电池电量快用完了，建议更换电池。
Note: Wireless Handle Need Two AA Battery；When the Low voltage indicator LED light；the battery is completely；Proposed to replace the battery
四、无线性能描述（RF Performance Description)
| 序号No. | 性能参数描述
Performance or Parameters Description |
| 1 | 采用2.4G无线RF传输技术，发射功率0DB，接收灵敏度-98DB
The RF is Standard with 2.4G ISM ,the Tx power is 0DB and the RX sensitivity is -98DB. |
| 2 | 具有64个跳频频道，每个频道间隔1MHZ
The RF has 64 channels,the channel gap is 1Mhz |
| 3 | 空旷直线传输距离大于15米
The transmission distance is further than 15 meters with no barrier |
| 4 | 智能无线技术，实现自动跳频，自动节约功耗，自动ID码学习
The protocol Designed with high performance； Low power consumption；Automatic learning ID Number |
| 5 | 采用跳频传输，抗干扰能力强；能自动避开无线路由器，2.4G无线耳机，蓝牙设备的干扰。
To jump frequency Adaptively when noised ,which can work with 2.4G wireless Mic ,Wlan and Bluetooth etc. devices. |
| 6 | 跳频传输技术，同一个房间，能支持32套设备，同时使用，相互不受影响
32 sets Wireless Handle work fine at the same time in one room ,with no-interference each other |
五、无线电子手轮WHB04 手摇脉冲发生器 手脉 雕刻机手轮使用说明
Operating Instructions of WHB04
WHB04手轮驱动安装(WHB04 SET UP)
A.安装了MACH3后,在MACH3安装目录下有个 “PlugIns” 文件夹,如果没有请建一个名为”PlugIns”的文件夹.然后把驱动文件XHC-ShuttlePro.dll拷贝到此文件夹\Mach3\PlugIns下.
When Mach3 is installed , there will be a folder created named “PlugIns” in theMach3 folder. This folder is the location to put and Plugin files that you want Mach3 to know about. Place “XHC-ShuttlePro.dll” in the \Mach3\PlugIns folder. Check and make sure it is there.
B. 插入MACH3 手轮的USB控制器到计算机的USB口.**次时,计算机会提示发现新硬件,并自动安装控制器需要的驱动.
Now that the XHC-ShuttlePro.dll file is in \Mach3\PlugIns, the next step is to connect the ShuttlePro. If you are certain that your ShuttlePro is working and your hardware is working then you can simply plug in the ShuttlePro to one of the USB ports.
C. 打开MACH3软件,在“Config”配置菜单下,选择”Config Plugins”配置插件.在弹出的配置插件窗口中,将” ShuttlePro-XHC-FOR-MACH3…”enable使能,这时会看到到有绿色的钩.然后点黄色的”config”配置按钮,会弹出键的配置窗口,在配置窗口中,你可以选择每个按键的功能.如果不选择,全部的按键将是默认功能.
Once the ShuttlePro is connected, start Mach3 and go to the “Config” menu choice and select “ConfigPlugins”. You should see the ShuttlePro choice with a green checkmark in front of it. If it is not checked, you can check it. The checkmark means that Mach3 found the ShuttlePro on startup. Click the “CONFIG” in yellow and set the buttons as you wish.
D. 退出配置窗口后, MACH3 手轮就能正常使用了.在MACH3软件使用前,你需要按”Reset”复位键,MACH3软件才能正常使用.
Once you have the proper button selected in the Mach3 ShuttlePro Plugin CONFIG menu, your Shuttle device should be working properly.
A、按键功能描述（Button Features Description）
B、窗口显示描述（LCD Display Features Description）
坐标值显示窗口：（Coordinates of the window）
C、进给和转速显示窗口 ：（Feed and speed display window）
| 对应图标 Corresponding icon | 名称
Name | 按键功能描述Key function description |
 | 停止按钮
Stop button | 按下该键，停止机床Press the button to stop machine |
 | 开始/暂停按钮
Start / Pause button | 机床处于运行状态，按下该键，机床暂停加工机床处于暂停状态，按下该键，机床继续运行。
Machine is running, press the button, the machine to suspend processing Machine is paused, press this button, the machine continues to run |
 | 倒退
Rewind | 返回到程序的开始
return to the program start |
 | 复位Reset | 复位程序
reset program |
 | 回工件原点按钮
Back to the origin Button | 按下该键，机床执行回工件原点操作
Press this key piece back to the origin of the implementation machine |
 | X分中按钮
X Coordinates 1 / 2 Button | 将X工件坐标分中
X Coordinates 1 / 2 |
 | Y分中按钮
Y Coordinates 1 / 2 Button | 将Y工件坐标分中
Y Coordinates 1 / 2 |
 | Z**高度设定
Z Coordinates 1 / 2 Button | 将当前Z轴的工件坐标做为Z轴的退刀点
Z Coordinates 1 / 2 |
 | X=0按钮
X oordinates=0 Button | 将当前坐标设置为X轴工件坐标
X coordinate is set to the current Workpiece coordinates axis |
 | Y=0按钮
Y oordinates=0 Button | 将当前坐标设置为Y轴工件坐标
Y coordinate is set to the current Workpiece coordinates a |
…… 详情请点击下载
成都新宏畅无线科技有限公司
Chengdu XingHongChang Wireless Technology Co., Ltd
www.cdxhctech.com
D、按键功能描述（Key function description）
六、使用功能描述（Features Description）
三、直流电气特性（DC Description）